Pressures during roller squeezing of leather
DOI:
https://doi.org/10.47813/2782-2818-2023-3-4-0216-0230Keywords:
roller pressing of leather, contact problems, roll contact curves, contact stresses, hydraulic pressures.Abstract
With the solution of contact and hydraulic problems of roller squeezing of leather, mathematical models of the patterns of distribution of normal stress and hydraulic squeezers during roller squeezing of leather were obtained. It was revealed that normal stresses change from zero at the beginning and end of the roll contact zone to a maximum at the point of maximum skin deformation, and hydraulic pressures change from zero at the beginning of the roll contact zone to a maximum at the point of maximum leather deformation, after which it is equal to zero until the end of the roll contact zone.
References
Бурмистров А.Г. Машины и аппараты производства кожи и меха. М.: Колос С; 2006. 384.
Новиков Н.Е. Прессование бумажного полотна. М.: Лесная промышленность; 1972. 242.
Кузнецов Г.К. Исследование и методика проектирования валковых отжимных устройств текстильных машин: Дис. … докт. техн. наук. Кострома; 1970. 287.
Хуррамов Ш.Р. Теоретические основы контактного взаимодействия в двухвалковых модулях и ее использование в совершенствовании процессов механической обработки. Дисс. …докт. техн. наук. Т.; 2022. 225.
Бурмистров А.Г., Ибара Поль, Чурсин В.И., Илюхина О.А. Исследование деформационных характеристик дермы на отдельных стадиях кожевенного производства. Известия ВУЗов. Технология легкой промышленности. 1992; 3-4: 40-43.
Колычев М.В., Кокушин Н.Н. Исследование деформационных свойств прессовых сукон бумагоделательных машин. Целлюлоза. Бумага. Картон. 2015; 6: 68-72.
Курбанова Ф.З. Исследование контактного взаимодействия в валковых парах для совершенствования процессов механической обработки листовых материалов. Дисс. …докт фил. по техн.наук. Т.; 2022. 138.
Фомин Ю.Г. Разработка теоретических основ и средств повышения эффективности обработки тканей валковыми модулями отделочных машин: Дис. … докт. техн. наук. Иваново; 2001. 406.
Селюк Д.В., Карпухин С.Л. Оценка влияния режима работы эластичного колеса на
параметры его качения по деформируемой опорной поверхности. Журнал автомобильных инженеров. 2016; 6(101): 14-18.
Полумисков С.А. Исследование валкового пропиточного устройства и разработка метода расчета его конструктивных и технологических параметров: Автореф. дис. …канд. техн. наук. Иваново; 1997. 17.
Downloads
Published
How to Cite
Conference Proceedings Volume
Section
License
Copyright (c) 2023 G. A. Bahadirov, Sh. R. Khurramov, K. Yu. Aliboev
This work is licensed under a Creative Commons Attribution 4.0 International License.
The journal MIST - "Modern Innovations, Systems and Technologies" publishes materials under the terms of the Creative Commons Attribution 4.0 International (CC BY 4.0) license, hosted on the official website of the non-profit corporation Creative Commons:
This work is licensed under a Creative Commons Attribution 4.0 International License.
This means that users can copy and distribute materials in any medium and in any format, adapt and transform texts, use content for any purpose, including commercial ones. At the same time, the terms of use must be observed - an indication of the author of the original work and the source: you should indicate the output of the articles, provide a link to the source, and also indicate what changes have been made